Rear Gaz shocks, Red dot cones, radius arms, rear subframe
Turbo Mini Forums

Rear Gaz adjustable shocks Lower ride hight - less than 2k miles old couple spots of corrosion £50 pair
Pair Red dot cones, like new, little surface rust on the steel bands, every road mini should have these imo, £50 pair

rear subframe
2 pairs of radius arms - one new built through out with new back plates minifins and mintex shoes
- think these have been snapped up by the donny mini club lot more details if they come available






my add on donny mini site

The other set is off mine there lightened slightly covered less than 2k miles was built with new back plates new bearings new mintex shoes (origional un spacered) ally minifin drums with extra spacers and they were reconditioned fully inc radius arm pins and bushes. Painted nice yellow but chipped now lol looking for £ 150 or £100 for the arms and brakes shoes and I keep the ally minifins
these are the yellow set, hopefully the dirty set will go tommorow, although asking £50 for those







and my subframe, also painted in the worst paint i have ever used ( its easy to remove though )
i fitted this new in 2006, june 2007 it came off the road for its last rebuild so its still not that old and has very little surface rust



it was modified for a flat boot floor and also so my big diffuser could squeeze through,
the original cross member is there so could be put back to standard with a little welding
looking for £50 for that


[img][/img]

Edited by Brett on 11th Jan, 2014.

Yes i moved to the darkside

Instagram @jdm_brett

I'll have the cones. I have a feeling my standard ones will be too soft.

do-nuts sold to that man!!

Yes i moved to the darkside

Instagram @jdm_brett

Shocks are a bargain

i think there competitively priced, might even be able to provide them boxed in original box lol

-just remembered there the lowered hight ones

Yes i moved to the darkside

Instagram @jdm_brett

Could you possibly tell me what the closed and extended length are, please ?

Just from the centre of the eye to the midpoint in the pin, where the two steel cup washers meet.

no probs there - 9 3/4 inch closed, 13.5 inch open

when you tigthen them up i bet thats 9 1/2closed though

Edited by Brett on 10th Jan, 2014.

Yes i moved to the darkside

Instagram @jdm_brett

Thanks, but not a long enough stroke for what I had in mind.

you can pretty much pick the open and closed lengths if you phone them up and order direct
these are the shorter height ones too i would have thought the standard hight ones will be longer

Edited by Brett on 10th Jan, 2014.

Yes i moved to the darkside

Instagram @jdm_brett

Shame im going to a beam otherwise id snap them up

I'll take the shocks. Also interested in the new built up radius arms for sure

moved to the first post

Edited by Brett on 11th Jan, 2014.

Yes i moved to the darkside

Instagram @jdm_brett

If the yellow arms are still available I'll take 'em (complete as they are).

How much for the foot and homers hand?

www.apsbikes.co.uk

On 12th Jan, 2014 APS said:
How much for the foot and homers hand?

Edited by Brett on 12th Jan, 2014.

Yes i moved to the darkside

Instagram @jdm_brett

If Andy decides the cones are going to be to hard for his derriere, I'll have second dips on them bud.

What the mind can conceive the mini can achieve
MITP 2012 17.01 seconds 1/4 mile against "The Don"
MITP 2013 16.83 seconds 1/4 mile

There gone and payed for mate

Yes i moved to the darkside

Instagram @jdm_brett

no worries

What the mind can conceive the mini can achieve
MITP 2012 17.01 seconds 1/4 mile against "The Don"
MITP 2013 16.83 seconds 1/4 mile

All sold and delivered now, cheers

Yes i moved to the darkside

Instagram @jdm_brett

Yes i moved to the darkside

Instagram @jdm_brett

If you are in the area that would be good. planning to have a garage day, wife permitting.