| Page: |
| Home > 998cc > dump valve fitting kit | |||||||
 " alt="User Avatar" width="100" height="100">52 Posts Member #: 1735 Advanced Member morton, lincolnshire |
30th Jun, 2009 at 09:07:47pm
saw this ebay item today what do you guys think is it worth it? i was thinking of getting the carb to manifold adaptor instead but not sure |
||||||
 667 Posts Member #: 5232 Post Whore basingstoke |
30th Jun, 2009 at 09:59:08pm
no link posted mate.
Mr. Prawn, the friendly Crustacean- slowly making steps towards forced induction. |
||||||
 16540 Posts Member #: 4241 King Gaycharger, butt plug dealer, Sheldon Cooper and a BAC but generally a niceish fella if you dont mind a northerner Rotherham, South Yorkshire |
30th Jun, 2009 at 10:06:40pm
Couple of pipes, few clamps and a t piece at a guess.
On 11th Feb, 2015 robert said:
i tried putting soap on it , and heating it to brown , then slathered my new lube on it 
|
||||||
|
" alt="User Avatar" width="100" height="100"> 52 Posts Member #: 1735 Advanced Member morton, lincolnshire |
30th Jun, 2009 at 10:12:57pm
ooops sorry forgot the link
|
||||||
 4629 Posts Member #: 20 My sister is so fit I won't show anyone her picture Lake District |
30th Jun, 2009 at 11:18:43pm
You'll have to weld the provided "spout" to the plenum, plus it's a fair bit of money for just a dump valve & a couple of hoses. |
||||||
|
667 Posts Member #: 5232 Post Whore basingstoke |
30th Jun, 2009 at 11:19:56pm
I'd say that's of just about no use to you at all!
Mr. Prawn, the friendly Crustacean- slowly making steps towards forced induction. |
||||||
 12307 Posts Member #: 565 Carlos Fandango Burnham-on-Crouch, Essex |
30th Jun, 2009 at 11:22:21pm
alernatilvly you can get silicon T's On 28th Aug, 2011 Kean said:
At the risk of being sigged... Joe, do you have a photo of your tool? http://www.turbominis.co.uk/forums/index.p...9064&lastpost=1 https://joe1977.imgbb.com/ |
||||||
 84 Posts Member #: 5645 Advanced Member middlesex ( near heathrow ) |
1st Jul, 2009 at 09:24:14am
On 30th Jun, 2009 Prawn said:
I'd say that's of just about no use to you at all! If you want to install a DV without modifying the plenum, the only option is to run a full size T-piece in your cold side IC line with a 1'' take off, then hook this up to the DV using a 1'' silicon coupler. then rig up the vacuum feed from the inlet as normal This would do it if you wanted to use a metal T: http://cgi.ebay.co.uk/TWIN-PISTON-DUMP-VAL...93%3A1|294%3A50 Or alternatively, you could simply replace a normal silicon coupler for one with a DV take off like this: http://cgi.ebay.co.uk/63mm-2-1-2-ID-T-Piec...93%3A1|294%3A50 Don't go slow !!! Go Turbo :)))))) |
||||||
|
2488 Posts Member #: 1954 Post Whore Luton Bedfordshire |
1st Jul, 2009 at 01:58:00pm
The kit from Minispeed comes with the sandwich plate with the vaccum line fitted to boot. Own the day
|
||||||
|
" alt="User Avatar" width="100" height="100"> 52 Posts Member #: 1735 Advanced Member morton, lincolnshire |
1st Jul, 2009 at 06:23:20pm
thanks guys very helpful, one other question were do i put the vacumm pipe in the inlet? dont seem to be anywere for it? |
||||||
|
12307 Posts Member #: 565 Carlos Fandango Burnham-on-Crouch, Essex |
1st Jul, 2009 at 06:29:31pm
somwhere on the inlet manifold. On 28th Aug, 2011 Kean said:
At the risk of being sigged... Joe, do you have a photo of your tool? http://www.turbominis.co.uk/forums/index.p...9064&lastpost=1 https://joe1977.imgbb.com/ |
||||||
|
2488 Posts Member #: 1954 Post Whore Luton Bedfordshire |
1st Jul, 2009 at 06:43:17pm
Was down at the Ace Cafe and spotted a Turbo with the vaccum taken from where the part throttle lean off pipe plugs into the carb Own the day
|
||||||
|
12307 Posts Member #: 565 Carlos Fandango Burnham-on-Crouch, Essex |
1st Jul, 2009 at 07:04:32pm
on a lot of (all?) Hif's the vacum port for the dizzy works diferent to ordinary su's so can be used for the dump valve.
On 28th Aug, 2011 Kean said:
At the risk of being sigged... Joe, do you have a photo of your tool? http://www.turbominis.co.uk/forums/index.p...9064&lastpost=1 https://joe1977.imgbb.com/ |
||||||
| Home > 998cc > dump valve fitting kit | |||||||
|
|||||||
. The owner says it works just fine (obviously his setup was modified so as not to need the part throttle lean of pipe)| Page: |