1293 turbo saloon, update 26/06/14 running again, mot time
Turbo Mini Forums

Cheers mate

More proggress concluding with sausages

13.95 1/4 mile on a 2.95 fd. Carnt be that hard to beat!

Wheels again

13.95 1/4 mile on a 2.95 fd. Carnt be that hard to beat!

Slight update, been collectin a few parts. And trying to find a new backplate for my gt20 no luck sooo



And then I got this to replaced my shitty patchwork shell. Wants some work but its for the summer and winter ready for 2014

13.95 1/4 mile on a 2.95 fd. Carnt be that hard to beat!

Got camber?!

Those sausages look nice

Lots! Gota set it up.

And they were very very nice

13.95 1/4 mile on a 2.95 fd. Carnt be that hard to beat!

Had an hour on the car today.
Got the turbo built with new backplate and got the oil return almost done

13.95 1/4 mile on a 2.95 fd. Carnt be that hard to beat!

That will leak like a bitch!

Subframe won't rust

I run a supercharger and I don't care the TB is on the wrong side.
VEMS + 12 PSI + Liquid Intercooler = Small Bore FUN!

Just seen the first screen, and man that must be a loud exhaust!

I run a supercharger and I don't care the TB is on the wrong side.
VEMS + 12 PSI + Liquid Intercooler = Small Bore FUN!

Nah its not that bad tbh. Not a patch on the gears anyway

13.95 1/4 mile on a 2.95 fd. Carnt be that hard to beat!

Right dropped my mock up block in this morn and got it all offerd up.

Think it fits out of luck rather than careful planning.

Getting a kad bias setup next so hoping that will fit in the gap. Also will I need the pressure valve anymore and does it need to sit level?





Overall im happy with how its turning out, should look gd when its all done

Eden

13.95 1/4 mile on a 2.95 fd. Carnt be that hard to beat!

Nice work thr mate.

well done mate looking good

give em hell

Cheers lads,

Done a bit more mocking up today, checked the clutch mech and done the 1st part to the screamer.

Goin to run it as is before I do anymore to that





Eden

13.95 1/4 mile on a 2.95 fd. Carnt be that hard to beat!

That looks awfully close to the slave cylinder? Is it not going to fry the rubber grommet or something?

http://www.turbominis.co.uk/forums/index.p...tid=469104&fr=0

Guna wrap it and hope

Should be ok

13.95 1/4 mile on a 2.95 fd. Carnt be that hard to beat!

could make a heat shield going around the slave..

looking good mate

Craig

my mini van http://www.turbominis.co.uk/forums/index.php?p=vt&tid=448248

Cheers mate,

Decided to run high temp fluid in the clutch too. That coupled with the mani wrap should be fine

13.95 1/4 mile on a 2.95 fd. Carnt be that hard to beat!

check the clearance for the slave in the verto position.... as you'll probably end up running an RTS at some point

Will do joe, altho this clutch setup is serving me well atm

13.95 1/4 mile on a 2.95 fd. Carnt be that hard to beat!

Well my kad bias box came and it fits! Just





Should be able to get a rite crack on soon, had other cars holding me up

13.95 1/4 mile on a 2.95 fd. Carnt be that hard to beat!

oooh close!

that bit of the wastgaste should stay fairly cool so you shouldn't get a heat issue..... but do check how hot it gets anyway.

Il be keeping a close eye on everything for a good while, theres alot of hot things going on there

13.95 1/4 mile on a 2.95 fd. Carnt be that hard to beat!

nice one!

you can do anything if you set your mind to it...
i rather blow it up winning than keep it together losing.

finish date set for project 1... march 2018